รายละเอียด:
เสต็ปไดรฟ์เวอร์รุ่น M880A ขับกระแสสูง 1.8A-7.8A เพียง 4,990 บาท (ยังไม่รวมภาษี)
- รับประกันสินค้า 1 ปี
- ค่าจัดส่ง EMS 60 บาท
- ราคารวมภาษี 7% และค่าส่ง EMS แล้ว = 5,399 บาท
คุณสมบัติ
- ขับกระแสสเต็ปมอเตอร์ได้ตั้งแต่ 1.8 ถึง 7.8 แอมป์ต่อเฟส
- ปรับค่าความระเอียดสัญญาณควบคุมไ้ตั้งแต่ 400 ถึง 51,200 ไมโครสเตปต่อรอบ
- รับความถี่อินพุทได้สูงถึง 300 KHz
- รองรับสัญญาณทั้งแบบ Step / Direction และ CW/CCW
- รับแรงดันไฟฟ้าได้สูงถึง 24 ถึง 80 โวลท์ดีซี (มีผลต่อความเร็วและแรงบิดของมอเตอร์)
Introduction
ไมโครเสต็ปไดรฟ์เวอร์ รุ่น M880A เป็นเสต็ปไดรฟ์เวอร์ คุณภาสูงที่ใช้เทคโนโลยีการควบคุมแบบ pure-sinusoidal current control ตัวไดรฟ์สามารถปรับกระแสได้อย่างเหมาะสมกับชนิดของเสต็ปมอเตอร์ทีต่ออยู่ และยังไม่ทำให้เกิดสัญญาณรบกวน (Noise) รวมถึงไม่ทำให้มอเตอร์ร้อนและทำให้การเคลื่อนที่ของเสต็ปมอเตอร์เป็นไปอย่าง ราบรื่นอีกด้วย อีกทั้งยังทำให้เสต็ปมอเตอร์สามารถหมุนได้ที่ความเร็วสูง ไดรฟ์ตัวนี้จึงเหมาะกับการนำไปใช้กับ เสต็ปปิ้งมอเตอร์แรงบิดสูงชนิด 2 เฟส และ 4 เฟส
Features
|
• |
High performance, cost-effective |
|
• |
Supply voltage up to +80VDC |
|
• |
Output current up to 7.8A |
|
• |
Self-adjustment technology |
|
• |
Pure-sinusoidal current control technology |
|
• |
Pulse input frequency up to 300 KHz |
|
• |
TTL compatible and optically isolated input |
|
• |
Automatic idle-current reduction |
|
• |
16 selectable resolutions in decimal and binary, up to 51,200 steps/rev |
|
• |
Suitable for 2-phase and 4-phase motors |
|
• |
Support PUL/DIR and CW/CCW modes |
|
• |
Short-voltage, over-voltage, over-current and over temperature protection |
Applications
เหมาะ สมที่จะนำไปใช้งานกับเสต็ปปิ้งมอเตอร์ขนาดต่างๆได้อย่างมากมาย ตั้งแต่ขนาด NEMA 17 ถึง NEMA 34 และตัวไดรฟ์ยังสามารถนำไปใ้ช้งานกับเครื่องจักรกลประเภทต่างๆได้เช่น X-Y tables, engraving machines, labeling machines, laser cutters, pick-place devices และอื่นๆ
Electrical Specifications (Tj = 25oC/77oF)
Parameters
|
M880A
|
Min
|
Typical
|
Max
|
Unit
|
Output current
|
1.8
|
-
|
7.8 (5.6 RMS)
|
A
|
Supply voltage
|
+24
|
+68
|
+80
|
VDC
|
Logic signal current
|
7
|
10
|
16
|
mA
|
Pulse input frequency
|
0
|
-
|
300
|
KHz
|
Isolation resistance
|
500
|
|
|
Mohm
|
Mechanical Specifications (unit: mm[inch])

Pin Assignment and Description
Connector P1 Configurations
Pin Function
|
Details
|
PUL+
|
Pulse signal: In single pulse (pulse/direction) mode, this input represents pulse signal, active at each rising or falling edge (set by inside jumper J3); 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode (pulse/pulse) , this input represents clockwise (CW) pulse,active at high level or low level (set by inside jumper J3). For reliable response, pulse width should be longer than 1.5µs. Series connect resistors for current-limiting when +12V or +24V used.
|
PUL-
|
DIR+
|
DIR signal: In single-pulse mode, this signal has low/high voltage levels, representing two directions of motor rotation; in double-pulse mode (set by inside jumper J1), this signal is counter-clock (CCW) pulse,active at high level or low level (set by inside jumper J3). For reliable motion response, DIR signal should be ahead of PUL signal by 5µs at least. 4-5V when DIR-HIGH, 0-0.5V when DIR-LOW. Please note that motion direction is also related to motor-driver wiring match. Exchanging the connection of two wires for a coil to the driver will reverse motion direction.
|
DIR-
|
ENA+
|
Enable signal: This signal is used for enabling/disabling the driver. High level (NPN control signal, PNP and Differential control signals are on the contrary, namely Low level for enabling.) for enabling the driver and low level for disabling the driver. Usually left UNCONNECTED (ENABLED).
|
ENA-
|
Connector P2 Configurations
Pin Function
|
Details
|
VDC
|
Power supply, 24~80 VDC, Including voltage fluctuation and EMF voltage.
|
GND
|
Power Ground.
|
A+, A-
|
Motor Phase A
|
B+, B-
|
Motor Phase B
|
Selecting Microstep Resolution and Driver Output Current

This driver uses an 8-bit DIP switch to set microstep resolution, and motor operating current, as shown below:
Microstep Resolution Selection
Microstep resolution is set by SW5, 6, 7, 8 of the DIP switch as shown in the following table:
Microstep
|
Steps/rev.(for 1.8o motor)
|
SW5
|
SW6
|
SW7
|
SW8
|
2
|
400
|
ON
|
ON
|
ON
|
ON
|
4
|
800
|
OFF
|
ON
|
ON
|
ON
|
8
|
1600
|
OFF
|
OFF
|
ON
|
ON
|
16
|
3200
|
ON
|
OFF
|
ON
|
ON
|
32
|
6400
|
ON
|
ON
|
OFF
|
ON
|
64
|
12800
|
OFF
|
ON
|
OFF
|
ON
|
128
|
25600
|
OFF
|
OFF
|
OFF
|
ON
|
256
|
51200
|
ON
|
OFF
|
OFF
|
ON
|
5
|
1000
|
ON
|
ON
|
ON
|
OFF
|
10
|
2000
|
OFF
|
ON
|
ON
|
OFF
|
20
|
4000
|
OFF
|
OFF
|
ON
|
OFF
|
25
|
5000
|
ON
|
OFF
|
ON
|
OFF
|
40
|
8000
|
ON
|
ON
|
OFF
|
OFF
|
50
|
10000
|
OFF
|
ON
|
OFF
|
OFF
|
100
|
20000
|
ON
|
OFF
|
OFF
|
OFF
|
200
|
40000
|
OFF
|
OFF
|
OFF
|
OFF
|
Current Settings
The first three bits (SW1, 2, 3) of the DIP switch are used to set the dynamic current. Select a setting closest to your motor's required current.
Peak Current
|
RMS Current
|
SW1
|
SW2
|
SW3
|
2.8 A
|
2.0 A
|
ON
|
ON
|
ON
|
3.5 A
|
2.5 A
|
OFF
|
ON
|
ON
|
4.2 A
|
3.0 A
|
ON
|
OFF
|
ON
|
4.9 A
|
3.5 A
|
OFF
|
OFF
|
ON
|
5.7 A
|
4.1 A
|
ON
|
ON
|
OFF
|
6.4 A
|
4.6 A
|
OFF
|
ON
|
OFF
|
7.0 A
|
5.0 A
|
ON
|
OFF
|
OFF
|
7.8 A
|
5.6 A
|
OFF
|
OFF
|
OFF
|
Note: Due to motor inductance, the actual current in the coil may be smaller than the dynamic current setting, particularly under high speed condition.
Typical Connection

M880A User Manual PDF
สอบถามข้อมูลเพิ่มเติมได้ที่
คุณพงษ์ศักดิ์ ป่วนเทียน
เบอร์ 081 3344 239