Line ID: @scnc (ต้องมี @ นำหน้า)

เสต็ปไดร์เวอร์ รุ่น DM1182ขับกระแสสูง 0.5A to 8.2A

฿18,560.00 ฿12,800
ตัวขับสเต็ปปิ้งมอเตอร์ ขับกระแสสูง 0.5A to 8.2A แบบไมโครสเต็ป ที่ปรับค่าได้ตั้งแต่from full-step to 102,400 ไมโครสเต็ป รับสัญญาณควบคุฒแบบ Pluse/Direction และ CW/CCW
เหลือ 10 ชิ้น
ซื้อเลย
หยิบลงตะกร้า
  • หมวดหมู่ : สเต็ปมอเตอร์ และชุดไดร์ฟ
  • รหัสสินค้า : 000051

รายละเอียดสินค้า เสต็ปไดร์เวอร์ รุ่น DM1182ขับกระแสสูง 0.5A to 8.2A

 รุ่น DM1182 (ยังไม่รวมภาษีและค่าจัดส่ง)

 - รับประกันสินค้า 1 ปี

 - ค่าจัดส่ง EMS 60 บาท

 - ราคารวมภาษี 7% และค่าส่ง EMS แล้ว

 

 

Features

 

  • Extra-low motor noise offers excellent quietness
  • Anti-Resonance, provides optimum torque and nulls mid-range instability
  • Self-test and Auto-configuration technology, offers optimum responses with different motors
  • Microstep resolutions programmable, from full-step to 102,400 steps/rev
  • Supply voltage up to 150 VAC
  • Output current programmable, from 0.5A to 8.2A 
  • Pulse input frequency up to 200 KHz
  • Automatic idle-current reduction 
  • Supports PUL/DIR and CW/CCW modes

Description

The DM1182 is a high voltage, versatility fully digital stepping drive based on a DSP with advanced control algorithm.  It brings a unique level of system smoothness, providing optimum torque and nulls mid-range instabilityMotor auto-test and parameter auto-configuration technology offers optimum responses with different motors and easy-to-use. The driven motors can run with much smaller noise, lower heating, smoother movement than most of the drivers on the markets. Its unique features make the DM1182 an ideal solution for applications that require low-speed smoothness.

* Pb-Free or CE/UL approved versions optional. Contact Leadshine or see more information in its hardware manual please.

Specifications

 

Electrical Specifications (Tj = 25oC/77oF)

 

Parameters

DM1182

Min

Typical

Max

Unit

Output current

0.5

-

8.2 (5.9 RMS)

A

Supply voltage

80(113)

110(155)

150(212)

VAC(VDC)

Logic signal current

7

10

20

mA

Pulse input frequency

0

-

200

kHz

Isolation resistance

500

 

 

Connector P1 Configurations

 

 

Pin Functions

Details

PUL+

Pulse signal: In single pulse (pulse/direction) mode, this input represents pulse signal, each rising or falling edge active (software configurable); 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode (pulse/pulse) , this input represents clockwise (CW) pulse,active both at high level and low level (software configurable). For reliable response, pulse width should be longer than 2.5μs. Series connect resistors for current-limiting when +12V or +24V used. The same as DIR and ENA signals.

PUL-

DIR+

DIR signal: In single-pulse mode, this signal has low/high voltage levels, representing two directions of motor rotation; in double-pulse mode (software configurable), this signal is counter-clock (CCW) pulse,active both at high level and low level (software configurable). For reliable motion response, DIR signal should be ahead of PUL signal by 5μs at least. 4-5V when DIR-HIGH, 0-0.5V when DIR-LOW. Please note that rotation direction is also related to motor-driver wiring match. Exchanging the connection of two wires for a coil to the driver will reverse motion direction.

DIR-

ENA+

Enable signal: This signal is used for enabling/disabling the driver. High level (NPN control signal, PNP and Differential control signals are on the contrary, namely Low level for enabling.) for enabling the driver and low level for disabling the driver. Usually left UNCONNECTED (ENABLED). When use it, the ENA signal should ahead the PUL signal at least 100ms due to of soft-start feature of the DM1182.

ENA-

FAULT+

Fault Signal: Open collector fault output. High impedance between FAULT+ and FAULT- during normal operation and low impedance when over-voltage, under-voltage, over-current and phase error protection. MAX: 30VDC,  20mA.

FAULT-

 

 

 

Connector P2 Configurations

  

 

Pin Function

Details

PE

Recommend connect this port to the ground for better safety.

AC

AC power supply inputs. If AC input, recommend use isolation transformers with theoretical output voltage of 80~150VAC. DC input range is 113~212VDC

AC

A+, A-

Motor Phase A

B+, B-

Motor Phase B

 

Microstep & Current

 

Microstep resolutions and output current are programmable, the former can be set from full-step to 102,400 steps/rev and the latter can be set from 0.5A to 8.2A .

 

 

However, when it’s not in software configured mode, this drive uses an 8-bit DIP switch to set microstep resolution, and motor operating current, as shown below:

 

 

 

Microstep Resolution Selection

 

When it's not in software configured mode, microstep resolution is set by SW5, 6, 7, 8 of the DIP switch as shown in the following table:

 

 

    Microstep

  Steps/rev.(for 1.8o motor)

SW5

SW6

SW7

SW8

1 to 512

Default/Software configured

on

on

on

on

2

400

off

on

on

on

4

800

on

off

on

on

8

1600

off

off

on

on

16

3200

on

on

off

on

32

6400

off

on

off

on

64

12800

on

off

off

on

128

25600

off

off

off

on

5

1000

on

on

on

off

10

2000

off

on

on

off

20

4000

on

off

on

off

25

5000

off

off

on

off

40

8000

on

on

off

off

50

10000

off

on

off

off

100

20000

on

off

off

off

125

25000

off

off

off

off

 

 

 

Current Settings

 

When it's not in software configured mode, the first three bits (SW1, 2, 3) of the DIP switch are used to set the dynamic current. Select a setting closest to your motor's required current.

 

Peak Current

RMS Current

SW1

SW2

SW3

Default/Software configured (0.5 to 8.2A )

OFF

OFF

OFF

2.2A

1.6A

ON

OFF

OFF

3.2A

2.3A

OFF

ON

OFF

4.2A

3.2A

ON

ON

OFF

5.2A

3.7A

OFF

OFF

ON

6.3A

4.4A

ON

OFF

ON

7.2A

5.2A

OFF

ON

ON

8.2A

5.9A

ON

ON

ON

 

 

Typical Connections

 
 

 

Mechanical Specifications (unit: mm [inch])

 

 

 

สอบถามข้อมูลเพิ่มเติมได้ที่ 

คุณพงษ์ศักดิ์ ป่วนเทียน 

เบอร์ 081 3344 239