Line ID: @scnc (ต้องมี @ นำหน้า)

เสต็ปไดรฟ์เวอร์รุ่น M880A ขับกระแสสูง 1.8A-7.8A เพียง 4,990 บาท

฿6,700.00 ฿4,990
ตัวขับสเต็ปมอเตอร์ขนาด 1.8 -7.8 แอมป์/เฟส รับแรงดัน 24 - 80 VDC ปรับความระเอียด 400 - 51,200 Step/rev และรับความถี่สูงถึง 300 KHz ทั้งแบบ Pul/Dir แลพ CW/CCW
เหลือ 8 ชิ้น
ซื้อเลย
หยิบลงตะกร้า
  • หมวดหมู่ : สเต็ปมอเตอร์ และชุดไดร์ฟ
  • รหัสสินค้า : 000013

รายละเอียดสินค้า เสต็ปไดรฟ์เวอร์รุ่น M880A ขับกระแสสูง 1.8A-7.8A เพียง 4,990 บาท

เสต็ปไดรฟ์เวอร์รุ่น M880A ขับกระแสสูง 1.8A-7.8A เพียง 4,990 บาท (ยังไม่รวมภาษี)

 

 - รับประกันสินค้า 1 ปี

 - ค่าจัดส่ง EMS 60 บาท

 - ราคารวมภาษี 7% และค่าส่ง EMS แล้ว = 5,399 บาท

 

 

คุณสมบัติ

 - ขับกระแสสเต็ปมอเตอร์ได้ตั้งแต่ 1.8 ถึง 7.8 แอมป์ต่อเฟส

 - ปรับค่าความระเอียดสัญญาณควบคุมไ้ตั้งแต่ 400 ถึง 51,200 ไมโครสเตปต่อรอบ 

 - รับความถี่อินพุทได้สูงถึง 300 KHz

 - รองรับสัญญาณทั้งแบบ Step / Direction และ CW/CCW

 - รับแรงดันไฟฟ้าได้สูงถึง 24 ถึง 80 โวลท์ดีซี (มีผลต่อความเร็วและแรงบิดของมอเตอร์)

 

Introduction

ไมโครเสต็ปไดรฟ์เวอร์ รุ่น M880A เป็นเสต็ปไดรฟ์เวอร์ คุณภาสูงที่ใช้เทคโนโลยีการควบคุมแบบ pure-sinusoidal current control ตัวไดรฟ์สามารถปรับกระแสได้อย่างเหมาะสมกับชนิดของเสต็ปมอเตอร์ทีต่ออยู่ และยังไม่ทำให้เกิดสัญญาณรบกวน (Noise)  รวมถึงไม่ทำให้มอเตอร์ร้อนและทำให้การเคลื่อนที่ของเสต็ปมอเตอร์เป็นไปอย่าง ราบรื่นอีกด้วย อีกทั้งยังทำให้เสต็ปมอเตอร์สามารถหมุนได้ที่ความเร็วสูง ไดรฟ์ตัวนี้จึงเหมาะกับการนำไปใช้กับ เสต็ปปิ้งมอเตอร์แรงบิดสูงชนิด 2 เฟส และ 4 เฟส

Features

  • High performance, cost-effective
  • Supply voltage up to +80VDC
  • Output current up to 7.8A
  • Self-adjustment technology
  • Pure-sinusoidal current control technology
  • Pulse input frequency up to 300 KHz
  • TTL compatible and optically isolated input
  • Automatic idle-current reduction
  • 16 selectable resolutions in decimal and binary, up to 51,200 steps/rev
  • Suitable for 2-phase and 4-phase motors
  • Support PUL/DIR and CW/CCW modes
  • Short-voltage, over-voltage, over-current and over temperature protection

 

Applications

เหมาะ สมที่จะนำไปใช้งานกับเสต็ปปิ้งมอเตอร์ขนาดต่างๆได้อย่างมากมาย ตั้งแต่ขนาด NEMA 17 ถึง NEMA 34 และตัวไดรฟ์ยังสามารถนำไปใ้ช้งานกับเครื่องจักรกลประเภทต่างๆได้เช่น X-Y tables, engraving machines, labeling machines, laser cutters, pick-place devices และอื่นๆ

 

Electrical Specifications (Tj = 25oC/77oF)
 

Parameters

M880A

Min

Typical

Max

Unit

Output current

1.8

-

7.8 (5.6 RMS)

A

Supply voltage

+24

+68

+80

VDC

Logic signal current

7

10

16

mA

Pulse input frequency

0

-

300

KHz

Isolation resistance

500

 

 

Mohm

 

Mechanical Specifications (unit: mm[inch])

 

Pin Assignment and Description

Connector P1 Configurations

Pin Function

Details

PUL+

Pulse signal: In single pulse (pulse/direction) mode, this input represents pulse signal, active at each rising or falling edge (set by inside jumper J3); 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode (pulse/pulse) , this input represents clockwise (CW) pulse,active at high level or low level (set by inside jumper J3). For reliable response, pulse width should be longer than 1.5µs. Series connect resistors for current-limiting when +12V or +24V used.

PUL-

DIR+

DIR signal: In single-pulse mode, this signal has low/high voltage levels, representing two directions of motor rotation; in double-pulse mode (set by inside jumper J1), this signal is counter-clock (CCW) pulse,active at high level or low level (set by inside jumper J3). For reliable motion response, DIR signal should be ahead of PUL signal by 5µs at least. 4-5V when DIR-HIGH, 0-0.5V when DIR-LOW. Please note that motion direction is also related to motor-driver wiring match. Exchanging the connection of two wires for a coil to the driver will reverse motion direction.

DIR-

ENA+

Enable signal: This signal is used for enabling/disabling the driver. High level (NPN control signal, PNP and Differential control signals are on the contrary, namely Low level for enabling.) for enabling the driver and low level for disabling the driver. Usually left UNCONNECTED (ENABLED).

ENA-

 

Connector P2 Configurations

Pin Function

Details

VDC

Power supply, 24~80 VDC, Including voltage fluctuation and EMF voltage.

GND

Power Ground.

A+, A-

Motor Phase A

B+, B-

Motor Phase B

 

Selecting Microstep Resolution and Driver Output Current


This driver uses an 8-bit DIP switch to set microstep resolution, and motor operating current, as shown below:

 

Microstep Resolution Selection

Microstep resolution is set by SW5, 6, 7, 8 of the DIP switch as shown in the following table:

Microstep

Steps/rev.(for 1.8o motor)

SW5

SW6

SW7

SW8

2

400

ON

ON

ON

ON

4

800

OFF

ON

ON

ON

8

1600

OFF

OFF

ON

ON

16

3200

ON

OFF

ON

ON

32

6400

ON

ON

OFF

ON

64

12800

OFF

ON

OFF

ON

128

25600

OFF

OFF

OFF

ON

256

51200

ON

OFF

OFF

ON

5

1000

ON

ON

ON

OFF

10

2000

OFF

ON

ON

OFF

20

4000

OFF

OFF

ON

OFF

25

5000

ON

OFF

ON

OFF

40

8000

ON

ON

OFF

OFF

50

10000

OFF

ON

OFF

OFF

100

20000

ON

OFF

OFF

OFF

200

40000

OFF

OFF

OFF

OFF

 

Current Settings

The first three bits (SW1, 2, 3) of the DIP switch are used to set the dynamic current. Select a setting closest to your motor's required current.

Peak Current

RMS Current

SW1

SW2

SW3

2.8 A

2.0 A

ON

ON

ON

3.5 A

2.5 A

OFF

ON

ON

4.2 A

3.0 A

ON

OFF

ON

4.9 A

3.5 A

OFF

OFF

ON

5.7 A

4.1 A

ON

ON

OFF

6.4 A

4.6 A

OFF

ON

OFF

7.0 A

5.0 A

ON

OFF

OFF

7.8 A

5.6 A

OFF

OFF

OFF

Note: Due to motor inductance, the actual current in the coil may be smaller than the dynamic current setting, particularly under high speed condition.

 

Typical Connection

 

M880A User Manual PDF

 

สอบถามข้อมูลเพิ่มเติมได้ที่

คุณพงษ์ศักดิ์ ป่วนเทียน

เบอร์ 081 3344 239